Mac word 15.29 print features how to#
Mac word 15.29 print features serial#
Mac word 15.29 print features drivers#
Mac word 15.29 print features driver#
Mac word 15.29 print features code#

With the USB connector facing up, we connect one side of the jumper wire to the top of J8 and the other side to the bottom of SOP2.

We start by removing both jumpers J8 and SOP2 (if installed).

Here are the detailed step-by-step instructions: The following image shows a neat workaround using the J8 (TOP) connector together with the SOP2 (BOTTOM). It is required to set different jumpers to go from run-mode to program-mode and back again. However, by design the LaunchPad does not offer a very programmer friendly method for a quick build - test - debug loop.

Mac word 15.29 print features serial#

This will compile the binaries, upload the code, open the serial monitor, and run the application. The easiest way to get it on the LaunchPad is to press CTRL + M in Energia. Now it's time to connect the LaunchPad and upload our program! Connecting the LaunchPad What happens here is that we get the following sequence: The digitalWrite function is then used to write a value to a given address, e.g., 1 (named HIGH) to the address of the RED_LED or 0 (named LOW) to the address of the GREEN_LED. For all of them we use the OUTPUT setting (resolving to 1, whereas INPUT would resolve to 0). Therefore, we have to configure the pins which are connected to the LEDs in the beginning. Most of them can either be used for input or output. Most pins of the CC3200 are multiplexed, i.e.

Mac word 15.29 print features code#

Initially, our code may be as simple as follows: (Remember that whenever we can blink an LED we can basically control anything.)ДЄll the hardware addresses and definitions can be found in hardware/cc3200/variants/launchpad/pins_energia.h. The board comes with three LEDs that can be used for simple showcases, testing and prototyping. Make sure to also check out the example sketches in File / Examples. The reference section of the Energia homepage will be your best friend when programming the CC3200 LaunchPad, especially in figuring out the inbuilt IO functions. The compilation and flashing the code to the board is still done in the Energia window. You can then simply edit and save the x.ino file in your favorite editor. In File / Preferences we'll find the option to tell Energia that we are using an external editor. While you can do everything from the built in editor, you'll probably quickly get annoyed by it. We'll come back to the monitor in a second. The latter never finishes, as it is invoked over and over again (hence the name loop).ДЇor debugging purposes the serial monitor will be crucial.

setup is run once during the initialization, and loop is repeatedly called after the initialization. These two functions will be called from implicitly generated code and are therefore special. The board specific header file and the definitions for setup and loop have been made already.

Mac word 15.29 print features how to#

Energia already knows everything about the board and how to talk to it. Instead of writing everything from scratch ourselves, we typically only fill in the bodies of those two functions. Every sketch file contains two C-like functions, setup and loop. The most important file is an Energia project ( x.ino), which is always contained in a folder with the name of the file (by convention).

The output is shown in the black box on the bottom. It contains a code area with a mediocre text editor. The Energia IDE looks as presented in the next image. Unzip and run EnergiaFTDIDrivers2.2.18.pkg.

Mac word 15.29 print features drivers#

Download the CC3200 Drivers for macOS from here.

Mac word 15.29 print features driver#

The only thing we need to do is to tell Linux to use that driver when we plug in the CC3200 LaunchPad. On recent versions of Linux the FTDI kernel driver that is needed for the CC3200 LaunchPad is already installed. The CC3200 should be automatically recognized by Energia.ДЇor Windows 8 or later we may need to disable the signed driver feature, see this guide.

Unzip and run DPinst.exe for the 32-bit version or DPinst64.exe for 64-bit version of Windows.

Download the CC3200 Drivers for Windows from here.

The following instructions are useful to setup the drivers for Energia. The CC3200 should not be connected, otherwise we should remove it first. Energia: First-Time SetupДepending on the OS different instructions need to be followed. In case the Energia IDE has not been run (with the CC3200) previously we need to set everything up first. We can use the editor provided by Energia or any other editor, e.g., Sublime Text, Emacs, or vim.

Computer with Windows, Linux, or macOS and an USB port.

In order to fully cover this tutorial we need the following setup: Finally, we will query a web service via secure HTTP and adjust the blinking according to the response.

Then we will use one of the available sensors to switch the LED depending on the sensor readings. Initially, our target will be to get some LEDs blinking. In this sample we will work with the CC3200 LaunchPad. This is a small tutorial on working with the CC3200 LaunchPad from Texas Instruments.